BY PLUMBING GUIDE FOR INSTALLING A BATHTUB

By Plumbing Guide for Installing a Bathtub

By Plumbing Guide for Installing a Bathtub

Blog Article

Book Appointment

How do you really feel with regards to How to Install a Bathtub Yourself?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't exactly brain surgery, yet it does need strong plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably challenging task. If the old tub is easily available, the task can move speedily; if you have to open a wall surface to get rid of the old tub and also position the new bath tub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will require an assistant to move out the old tub and also set in the new one. Make sure you have actually certified on your own for the task and also are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed task, it is far better to think about employing one before you start. Possibilities are you might require a professional plumber to make tube links.
This post will help you mount a brand-new bath tub in your bathroom if you have already acquired a new tub and also do not need to alter the plan of your previous water system pipes.
Your devices and also product list need to consist of the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Planning for the Setup


    To start with, the supporting frame provided with the bath ought to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid pressure on the bathtub.
    Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washing machines.
    Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its last position.

    Removing Old Taps


    If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is detach the water supply. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the limited access that is frequently the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
    Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Utilizing both wood boards under its feet, place the tub in the required placement. The wooden boards are useful in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
    The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
    To install faucets, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
    Turn on the water system and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
    Ultimately, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the tub needs to wait till the bath tub has actually been utilized at the very least when as this will certainly settle it into its final setting.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place in between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be connected to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with wetness as well as possible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealant can break fairly very early if you do not take into account this motion prior to sealing.
    Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the floor tiles using water-resistant or waterproof adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I am just very enthusiastic about Tools You Need to Install a New Bathtub and I am assuming you enjoyed the new post. Enjoyed our review? Please share it. Help other people check it out. Many thanks for your time. Don't hesitate to check up our website back soon.


    Damage control? Call us.

    Report this page